Difference between revisions of "KTM 500 EXC"

From Mtc
Jump to navigationJump to search
 
(17 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
[http://www.ktm.com/us/enduro/500excusa/highlights.html#.U3PvzK1dV9Y 2014 KTM 500 EXC]
 
[http://www.ktm.com/us/enduro/500excusa/highlights.html#.U3PvzK1dV9Y 2014 KTM 500 EXC]
−
===500 EXC Issues===
+
*1.5L oil capacity, drain it, refill w/ 1.4, and check right hand sight bubble after riding it around. Should be at 1/2. Add a little more oil if low.
−
* 20140712:
+
* 20151122: 1596miles and 59.9hours, changed oil w/ 10/50 Motorex and swapped in "dirt" wheels.
−
** No OIL in it right now, don't fire it up.
+
* 20160425: 2284miles and 84 hours, changed oil w/ 10/50 Motul and cleaned bike.
−
** Need to swap in and adjust the Rekluse clutch master cylinder.
+
* [http://ktmtalk.com/showthread.php?441764-2012-KTM-350-EXC-F-Check-Adj-valve-clearances-(-quot-Building-the-Perfect-Wee-Beasty-quot-)&highlight=eticket KTMTalk thread on adjusting valves (id: emptycea)]
−
** Need to re-install the bash guard
 
−
** Need to install the HDB hand guards
 
−
** Sicass says something about the re-wire kit wrt the green signal light.
 
−
 
 
−
* cold clutch doesn't fully disengage.
 
−
** This is normal for the KTM, the oil needs to warm up.
 
−
* "shimmy" starting around 50mph which gets a little worse w/ more speed and settles into a cyclic on/off shimmy.
 
−
** Balance the wheels, 3oz in front and 3.75 in rear.
 
−
 
 
 
===Bags===
 
===Bags===
 +
* [http://www.altrider.com/altrider-hemisphere-saddlebag-holster-system/pid/1607 Altrider Hemisphere], makes two types, one kinda horseshoe and another closer to a standard double bag. Scope both.
 
*[http://www.ktmtwins.com/giant-loop-ktm-zigzag-handlebar-bag GiantLoop ZigZag Handlebar Bag $55] at KTM Twins. Looks like a solid bag and would be nice to cover the bars and store some basics for quick access.
 
*[http://www.ktmtwins.com/giant-loop-ktm-zigzag-handlebar-bag GiantLoop ZigZag Handlebar Bag $55] at KTM Twins. Looks like a solid bag and would be nice to cover the bars and store some basics for quick access.
 
*[http://www.ortliebusa.com/prodInfo.asp?pid=342&cid=2 Ortlieb Moto Speed Bags] $240, thinking these might be the way to go for the enduro but gotta figure out how to shield them from the exhaust sufficiently.
 
*[http://www.ortliebusa.com/prodInfo.asp?pid=342&cid=2 Ortlieb Moto Speed Bags] $240, thinking these might be the way to go for the enduro but gotta figure out how to shield them from the exhaust sufficiently.
Line 28: Line 20:
  
 
===Repair Kit===
 
===Repair Kit===
 +
*[http://dirt-bike-gear.com/tw.html Dirt Bike Gear Tool Wrap]
 
*[http://slavensracing.com/shop/wolfy-tool-roll-by-wolfman/ Wolfman toolroll $25@Slavens] Not sure this is the unit I want but it looks decent.
 
*[http://slavensracing.com/shop/wolfy-tool-roll-by-wolfman/ Wolfman toolroll $25@Slavens] Not sure this is the unit I want but it looks decent.
 
*[http://www.dirt-bike-gear.com/tools.html DirtBikeGear list]
 
*[http://www.dirt-bike-gear.com/tools.html DirtBikeGear list]
Line 68: Line 61:
 
*[http://www.nuetechonlinestore.com/SearchResults.asp?Cat=1 Neutech Tubliss] $160/pair [http://www.ebay.com/itm/like/350872198713?lpid=82 eBay], normally $100/wheel.
 
*[http://www.nuetechonlinestore.com/SearchResults.asp?Cat=1 Neutech Tubliss] $160/pair [http://www.ebay.com/itm/like/350872198713?lpid=82 eBay], normally $100/wheel.
  
−
Vendors:
+
===Vendors:===
 +
* [http://www.powercellperformance.com/product-category/adventure-1190/ PowerCell Performance] ... small shop, nice hand made stuff...
 +
* Rottweiler
 
* [http://www.hyderacing.com/store/dirtbike/ktm/450_4t.htm Hyde Racing].
 
* [http://www.hyderacing.com/store/dirtbike/ktm/450_4t.htm Hyde Racing].
 
* All KTM Parts: [http://www.rockymountainatvmc.com/v/54/11296/Dirt-Bike-KTM-500-EXC-2014 Rocky Mountain] carries.
 
* All KTM Parts: [http://www.rockymountainatvmc.com/v/54/11296/Dirt-Bike-KTM-500-EXC-2014 Rocky Mountain] carries.
  
−
More Detail and ramblings:
+
===More Detail and ramblings:===
−
*HEATED GRIPS:
+
====DAMPER:====
 +
* Most people recommend the Scotts. I went w/ them.
 +
**[http://www.gprstabilizer.com/prod_v4_dirt GPR steering damper] $495 (KTM EXC 13-14 Fat Bar: 9001-0078) $450@SBM.
 +
**[http://www.scottsonline.com/Stabilizer_Purchase2.php?Make=Ktm&Model=&Bike_ID=6793&Year=2014&Size=500&Fred=%20Exc&BI_ID=374983 Scotts Damper for KTM]... may trim this package down depending on what happens w/ HDB stuff.
 +
====HANDGUARDS PLUS...====
 +
*damper, bar lift, blinkers, fairing, lights...?  heated grips, heated vest plug, GPS/Phone charging, computer mount, GPS/Phone mount, ?
 +
*HDB: black handguards and black ano supports.
 +
*[http://www.highwaydirtbikes.com/HDB_Shop/index.php?app=ccp0&ns=display&ref=splash Highway Dirtbikes] has some nice hand guards, windshield, possibly light mounts and blinkers... nice button switches as well... may want to do a fully integrated unit w/ a Scotts Damper.ADVRIDER01 at checkout to get 10% off purchase.
 +
*[http://www.advrider.com/forums/showthread.php?t=542381&page=5 Pic] of HDB's setup w/ a GPR damper.
 +
====HEATED GRIPS:====
 
**Look into KTM options.
 
**Look into KTM options.
−
*HANDGUARDS PLUS... damper, bar lift, blinkers, fairing, lights...?  heated grips, heated vest plug, GPS/Phone charging, computer mount, GPS/Phone mount, ?
+
====LIGHTS:====
−
**HDB: black handguards and black ano supports.
 
−
**[http://www.highwaydirtbikes.com/HDB_Shop/index.php?app=ccp0&ns=display&ref=splash Highway Dirtbikes] has some nice hand guards, windshield, possibly light mounts and blinkers... nice button switches as well... may want to do a fully integrated unit w/ a Scotts Damper.ADVRIDER01 at checkout to get 10% off purchase.
 
−
**[http://www.advrider.com/forums/showthread.php?t=542381&page=5 Pic] of HDB's setup w/ a GPR damper.
 
−
*LIGHTS:
 
 
**[http://www.cyclopsadventuresports.com/3000-Lumen-H4-H6-LED-Headlight-bulb-_p_83.html LED upgrade for stock] $60.
 
**[http://www.cyclopsadventuresports.com/3000-Lumen-H4-H6-LED-Headlight-bulb-_p_83.html LED upgrade for stock] $60.
 
**[http://www.bajadesigns.com/ProductDetail?ItemNumber=490003 Baja Designs Squadron] $300 each.
 
**[http://www.bajadesigns.com/ProductDetail?ItemNumber=490003 Baja Designs Squadron] $300 each.
 
**EnduroTech lights look pretty nice and seem to fit in the stock housing w/ low/hi options but may not "throw" as well as they should.
 
**EnduroTech lights look pretty nice and seem to fit in the stock housing w/ low/hi options but may not "throw" as well as they should.
−
*DAMPER:
+
 
−
**[http://www.gprstabilizer.com/prod_v4_dirt GPR steering damper] $495 (KTM EXC 13-14 Fat Bar: 9001-0078) $450@SBM.
+
====FUELING:====
−
**[http://www.scottsonline.com/Stabilizer_Purchase2.php?Make=Ktm&Model=&Bike_ID=6793&Year=2014&Size=500&Fred=%20Exc&BI_ID=374983 Scotts Damper for KTM]... may trim this package down depending on what happens w/ HDB stuff.
+
* Fuel filter sock, put in tank cap area as a pre-filter.
−
*FUELING:
 
−
** Fuel filter sock, put in tank cap area as a pre-filter.
 
−
*RECLUSE:
 
−
**[http://www.rekluse.com/coreexp.shtml Recluse Core EXP]: $900 retail, SBM? + about 90min to install.  Do at an oil change.
 
−
*SKID PLATE:
 
−
** [http://www.globetrottin.com/Skid-plate--Composite-full-coverage-for-KTM-500-EXC-XCW_p_23.html RTE Skid Plate] $140 made of carbon/fiber/epoxy.  It is also apparently so tight to the covers that dirt gets between the plate and moto parts and wears on the moto... bike inner-tube between those points prevents the wear.
 
−
** [http://www.tmdesignworks.com/index.php?main_page=product_info&cPath=325_327_354&products_id=973 TM Designs] skid plate at $105.  Plastic but sounds solid.  Not quite as much coverage as the RTE tho.
 
 
* [http://slavensracing.com/shop/super-mini-fuel-filter-kit-by-golan/ Golan Fuel Filter] $60 for filter and clamps.  Use this to replace the small stock inline filters which tend to clog and stall the bike.
 
* [http://slavensracing.com/shop/super-mini-fuel-filter-kit-by-golan/ Golan Fuel Filter] $60 for filter and clamps.  Use this to replace the small stock inline filters which tend to clog and stall the bike.
−
*RIM LOCKS:
+
=====TPS stuff:=====
−
**[http://www.motionpro.com/motorcycle/partno/11-0058/ LiteLock Rim Locks] Cheap and lighter than stock, light enuf that you shouldn't need to balance the wheels according to some folks. 1.6 front and 2.15 rear.
+
*[https://www.youtube.com/watch?v=yupPUkzs-cM YouTube vid on adjusting TPS w/ a voltmeter]
−
*MIRRORS:
+
You don't need a TPS tool to adjust the TPS. Here's what you do;
−
**[http://www.doubletakemirror.com/build/ktm DoubleTake Mirrors] around $93 for a pair. I've also seen mirrors which fold into the hand guards, would like to compare the pros/cons of the Double Takes w/ those.  ...may just use integrated flip-outs into handguards.
+
 
−
*MISC:
+
# Remove the seat.
 +
# Locate the wiring harness just before the gas tank. It will have the rubber cover that is attached via a rubber loop. Open it.
 +
# Look for the Orange wire with the yellow stripe.
 +
# Use a small solid piece of wire and slide it down the Orange wire and make contact with the connection.
 +
# Attached + voltmeter side to the small wire and the - voltmeter wire to the neg battery terminal.
 +
# turn the key on, turn the bike on (do not start).
 +
# Read the TPS setting.
 +
 
 +
*BestDualSportBikes sells a unit that plugs into the TPS sensor but it's $100.
 +
*[http://www.tpstool.com/ TPSTool.com] adapter fits onto the TPS for reading with a voltmeter for around $40]
 +
 
 +
====RECLUSE Clutch:====
 +
*[http://www.rekluse.com/coreexp.shtml Recluse Core EXP]: $900 retail, SBM? + about 90min to install.  Do at an oil change.
 +
====SKID PLATE:====
 +
* [http://www.globetrottin.com/Skid-plate--Composite-full-coverage-for-KTM-500-EXC-XCW_p_23.html RTE Skid Plate] $140 made of carbon/fiber/epoxy.  It is also apparently so tight to the covers that dirt gets between the plate and moto parts and wears on the moto... bike inner-tube between those points prevents the wear.
 +
* [http://tmdesignworks.com/index.php?main_page=product_info&cPath=325_327_354&products_id=973 TM Designs] skid plate at $119.  Plastic but sounds solid. Try this one if the RTE I have needs replacing.
 +
 
 +
====MISC:====
 
**[http://dirttricks.com/ DirtTricks Cone Washer] and [http://dirttricks.com/product-category/sprockets rear sprockets] and [http://dirttricks.com/product-category/sprockets/front-sprockets/ktm-husaberg-beta front sprockets $37]: apparently these last long and are the way to go.
 
**[http://dirttricks.com/ DirtTricks Cone Washer] and [http://dirttricks.com/product-category/sprockets rear sprockets] and [http://dirttricks.com/product-category/sprockets/front-sprockets/ktm-husaberg-beta front sprockets $37]: apparently these last long and are the way to go.
 
====TANK:====
 
====TANK:====
 +
*The Acerbis comes recommended and seems to be the only reasonably priced bigger tank.
 
**[http://justgastanks.com/product_info.php?products_id=2857 JustGasTanks] has the Ascerbis 5.3gal in natural, $299 + shipping.
 
**[http://justgastanks.com/product_info.php?products_id=2857 JustGasTanks] has the Ascerbis 5.3gal in natural, $299 + shipping.
 
** [http://www.rockymountainatvmc.com/p/2851/41264/KTM-Fuel-Tank?v=11296 KTM 5gallon Tank] Fits: 2014 KTM 500 EXC Part# 1433310005 price: $359.99
 
** [http://www.rockymountainatvmc.com/p/2851/41264/KTM-Fuel-Tank?v=11296 KTM 5gallon Tank] Fits: 2014 KTM 500 EXC Part# 1433310005 price: $359.99
−
**[http://shop.ktm.com/int_en/powerparts/tanks/19-l-fuel-tank-5.html KTM PowerParts]... not sure how much it is or what parts are needed with it. Might wanna check out KTM Twins.
+
**[http://shop.ktm.com/int_en/powerparts/tanks/19-l-fuel-tank-5.html KTM PowerParts]... not sure how much it is or what parts are needed with it.  
 
** [http://www.mx1west.com/search.aspx?find=ktm+fuel+tank Acerbis Tanks]
 
** [http://www.mx1west.com/search.aspx?find=ktm+fuel+tank Acerbis Tanks]
 +
====Tank: Liquid bladder====
 +
*...probably just use Nalgene or Platypus bladders but consider lining an MSR Dromedary w/ tank sealant too.
 +
* [http://justgastanks.com/product_info.php?products_id=2061 6 gallon bladder at JustGasTanks] $449.
 
** What about finding soft gas bags for expansion?  Strap near standard tank and drain into tank when it'll take'm?
 
** What about finding soft gas bags for expansion?  Strap near standard tank and drain into tank when it'll take'm?
 
*** [http://liquidcontainment.com.au/category/12/Motor-Bike LiquidContainment] Fuel Bladders, look like the best bet so far... and [http://www.advrider.com/forums/showthread.php?t=290034 this ADVRider thread] seems the best so far for info.
 
*** [http://liquidcontainment.com.au/category/12/Motor-Bike LiquidContainment] Fuel Bladders, look like the best bet so far... and [http://www.advrider.com/forums/showthread.php?t=290034 this ADVRider thread] seems the best so far for info.

Latest revision as of 17:18, 25 April 2016

2014 KTM 500 EXC

  • 1.5L oil capacity, drain it, refill w/ 1.4, and check right hand sight bubble after riding it around. Should be at 1/2. Add a little more oil if low.
  • 20151122: 1596miles and 59.9hours, changed oil w/ 10/50 Motorex and swapped in "dirt" wheels.
  • 20160425: 2284miles and 84 hours, changed oil w/ 10/50 Motul and cleaned bike.
  • KTMTalk thread on adjusting valves (id: emptycea)

Bags

  • Altrider Hemisphere, makes two types, one kinda horseshoe and another closer to a standard double bag. Scope both.
  • GiantLoop ZigZag Handlebar Bag $55 at KTM Twins. Looks like a solid bag and would be nice to cover the bars and store some basics for quick access.
  • Ortlieb Moto Speed Bags $240, thinking these might be the way to go for the enduro but gotta figure out how to shield them from the exhaust sufficiently.

Repair Kit

  • spare front tube
  • duct tape
  • bailing wire
  • tools
  • spare levers
  • spare shifter/brake
  • tow line (1" webbing)
  • ...

Repair Kit

  • Fender pack
  • front tube
  • tire irons
  • rubber tubing/siphon
  • JB Weld stuff
  • clutch and brake levers
  • shift lever
  • rear brake lever
  • Clutch repair kit?
  • chain breaker
  • bicycle hand pump
  • valve stem remover
  • duct tape
  • safety wire
  • spare nuts/bolts

Parts

KTM Wheels: Front: 21x1.6 Rear: 18x2.15 RAD Wheels: Front: 21x1.6 Rear: 19x2.15

Likely Stuff:

Vendors:

More Detail and ramblings:

DAMPER:

  • Most people recommend the Scotts. I went w/ them.

HANDGUARDS PLUS...

  • damper, bar lift, blinkers, fairing, lights...? heated grips, heated vest plug, GPS/Phone charging, computer mount, GPS/Phone mount, ?
  • HDB: black handguards and black ano supports.
  • Highway Dirtbikes has some nice hand guards, windshield, possibly light mounts and blinkers... nice button switches as well... may want to do a fully integrated unit w/ a Scotts Damper.ADVRIDER01 at checkout to get 10% off purchase.
  • Pic of HDB's setup w/ a GPR damper.

HEATED GRIPS:

    • Look into KTM options.

LIGHTS:

FUELING:

  • Fuel filter sock, put in tank cap area as a pre-filter.
  • Golan Fuel Filter $60 for filter and clamps. Use this to replace the small stock inline filters which tend to clog and stall the bike.
TPS stuff:

You don't need a TPS tool to adjust the TPS. Here's what you do;

  1. Remove the seat.
  2. Locate the wiring harness just before the gas tank. It will have the rubber cover that is attached via a rubber loop. Open it.
  3. Look for the Orange wire with the yellow stripe.
  4. Use a small solid piece of wire and slide it down the Orange wire and make contact with the connection.
  5. Attached + voltmeter side to the small wire and the - voltmeter wire to the neg battery terminal.
  6. turn the key on, turn the bike on (do not start).
  7. Read the TPS setting.
  • BestDualSportBikes sells a unit that plugs into the TPS sensor but it's $100.
  • TPSTool.com adapter fits onto the TPS for reading with a voltmeter for around $40]

RECLUSE Clutch:

  • Recluse Core EXP: $900 retail, SBM? + about 90min to install. Do at an oil change.

SKID PLATE:

  • RTE Skid Plate $140 made of carbon/fiber/epoxy. It is also apparently so tight to the covers that dirt gets between the plate and moto parts and wears on the moto... bike inner-tube between those points prevents the wear.
  • TM Designs skid plate at $119. Plastic but sounds solid. Try this one if the RTE I have needs replacing.

MISC:

TANK:

  • The Acerbis comes recommended and seems to be the only reasonably priced bigger tank.

Tank: Liquid bladder

TIRES:

WHEELS:

    • Rad Racing in Utah has nice stuff and some good prices...
    • Woody's Wheels... ends up around $1900 for a "best" supermoto set of wheels... and may not include a rotor or sprocket.
    • Warp9 around $1K for a full setup including rotors and caliper spacer. These sound like they're a good bang/buck but might not hold up to extreme abuse.
    • DNA Wheels, similar to the Warp9's.
  • TUBLESS:
    • Tubliss sounds like the way to go, Phreaner digs'm as does his mechanic buddy Scott. $85@Slavens
    • Mousse/Bibs for going "airless", need to research pros/cons of this more. Sounds like they're heavier, do wear out, can generate heat...

Kickstand

Forums and Info

Retrieved from "http://wiki-mtc.eri.ucsb.edu/index.php?title=KTM_500_EXC&oldid=1031"